Fiberglass Pipe Insulation
Brand : Owens Corning / Johns Manville
- SKU:
- 0100000
- Unit Of Measure:
- Per 3ft Section
- Size is NOT Diameter:
- Refer to Sizing Instructions
Fiberglass Pipe Insulation covering is intended as a thermal insulation for both hot and cold service piping from -20°F to 1000°F. The pipe insulation is molded from heavy density resin bonded glass fibers that come in 3 foot long hinged sections. The fiberglass is wrapped with white All-Service Jacketing with a self-sealing lap (ASJ/SSL) for a quick and secure installation. Each 3 foot section of commercial hot and cold pipe insulation comes with a butt-strip tape (matching the white ASJ jacketing) that is used to connect two sections of fiberglass pipe insulation covering together.
Fiberglass Pipe Wrap Uses:
- Domestic Hot & Cold Water Pipes
- Hot Water Heating Pipes
- High Temperature Pipes
- Dual Temperature Pipes
- Steam Pipes (Low to High Pressure)
- Condensate Lines
- Refrigerated / Chilled Liquid Pipes
Choosing The Correct Size: There are two sizes you need to choose when ordering fiberglass pipe insulation, the "Pipe Size" and the "Insulation Thickness". The insulation thickness is the wall thickness of the fiberglass which varies from 1/2" up to 3" thick. For help selecting a fiberglass pipe insulation thickness see our Fiberglass Thickness Guide To determine which Pipe Size to order please see the link below (Note: Pipe Size is NOT the same as the pipe diameter):
CLICK HERE FOR PIPE SIZING CHART AND INSTRUCTIONS
Installation Instructions:
To install hot and cold pipe covering, simply open the hinged part of the commercial pipe insulation and place the opening over the pipe. The fiberglass piping insulation covering will self-close around the pipe. Once the fiberglass is fitted snug around the pipe, peel the release paper from the self-sealing lap and press the ASJ/SSL jacket closed from the middle towards the edges of the pipe insulation. Make sure to rub the jacket closed to ensure a secure seal. Seal two sections together with a piece of butt strip tape making sure to rub the tape to create a secure seal. Additional ASJ MAX Tape is recommended for large projects and projects that require multiple cuts of the insulation. Use of PVC Fitting Covers for elbows, tees, unions and other pipe fittings should be installed after installing fiberglass pipe insulation.
For more information: Fiberglass Pipe Insulation Datasheet
VIDEO: HOW TO INSTALL FIBERGLASS PIPE INSULATION
White ASJ Jacketing: A large majority of common size fiberglass pipe wrap insulation we ship is the new ASJ Max / HP ULTRA pipe insulation while some larger sizes and (3 x 1/2, 3-1/8 x 1/2, 4 x 1/2, and 4-1/8 x 1/2) will be Johns Manville Micro-Loc HP. The new ASJ Max / HP ULTRA jacketing has a poly top-coat over the ASJ paper which makes it easier to wipe clean and slightly water resistant (cannot be left exposed outdoors).
NOTE: Each unit is 3 linear feet of pipe covering. For example, if you need 9 linear feet, you only need to order 3 units.
BUY INSULATION PRODUCTS.COM ONLY SELLS AMERICAN MADE FIBERGLASS PIPE INSULATION PRODUCTS. DEPENDING ON SHIP TO LOCATION AND/OR PIPE SIZE WE MAY SHIP OWENS CORNING ASJ MAX OR JOHNS MANVILLE MICRO-LOC HP / HP ULTRA INSULATION. PLEASE CONTACT US WITH ANY QUESTIONS.
-
Steam pipe insulation
Product was well made. Easy to install. Easy to peel off adhesive backing and sticks well. Included seam covers fit and stick well. Had no problems whatsoever. Was delivered quickly, well packed and reasonably priced. Very Satisfied.
**We are glad you found the product to be easy to install and are very satisfied. Thanks ~ BIP -
Good Quality Products
The quality on this fiberglass is much higher than I have found at other stores. Each piece came with a piece of tape as well for taping up the separate pieces. I still have a little bit to go so I may need more!
**We are thrilled that you are happy with the quality of our Fiberglass Pipe Insulation. Remember we only sell USA Made Pipe Insulation! ~ BIP